| Application: | Household Appliances, Automatic Doors |
|---|---|
| Signal Transmission: | RF Remote Control |
| Type: | Button |
| Certification: | ISO9001, RoHS, FCC, CE |
| Universal: | Universal |
| Transmission Distance: | 50-100m |
| Samples: |
|---|
| Customization: |
|---|
Suppliers with verified business licenses
Audited Supplier
Programming
INSTRUCTION MANUAL
The radio control units included in the pack are already programmed and ready to use. Zones 1 and 2 can operate independently in bistable or timed mode.
SETTING THE MODE OF OPERATION:
ZONE1
BISTABLE: remove the jumper on terminals 1 and 2
TIMED:insert the jumper on terminals 1 and 2
ZONE2
BISTABLE: remove the jumper on terminals 2 and 3
TIMED:insert the jumper on terminals 2 and 3
RADIO CONTROL ACQUISITION :
ZONE1
1 . Press key P1 on the control unit once to program exit Z1 : the led will remain on.
2 . Press and hold the key to be acquired on the radio control unit until the LED on the main control unit starts to flash; release the key .
ZONE2
1 . Press key P1 on the control unit twice to program exit Z2 ; the led will remain on.
2 . Press and hold the key to be acquired on the radio control unit until the led starts to flash; release the key.
SETTING THE WORK TIME (time the exit is on - programmable up to a maximum of 4'30'')
Only if TIMED MODE is used
ZONE1
Press key P2 on the main control unit once to set the work time for exit Z1 , the LED will come on.
Wait a length of time equal to the WORK TIME to be set on exit Z1 , after which press key P2 again.
The LED will flash three times to confirm.
ZONE2
Press key P2 on the main control unit twice to set the work time for exit Z2,the LED will come on.
Wait a length of time equal to the WORK TIME to be set on exit Z2 , after which press key P2 again.
The LED will flash three times to confirm.
DELETING THE RADIO CONTROL CODES
Deleting an individual code:
Press and hold key P1 on the main control unit for 5 seconds (release the key);the LED will remain on.Press the key on the radio control unit to be canceled until the LED begins to flash.
Deleting all codes:
Press and hold key P1 on the main control unit for approx.10 seconds; the LED will come on.Then release the key.The LED will emit 3 flashes to confirm the deletion of all the codes.
Note for Installation
WARNING ! it is important the following manual be followed for safety reasons . Incorrect installation or improper use of the product can lead to severe damage to property and / or persons.
l The packaging materials should be kept out of the reach of children since they are potentially hazardous.
l The device must only be installed by a qualified installer.
l We declines all responsibility resulting from improper use or any use other than that indicated in this documentation.
l Do not modify the device in any way.
l Disconnect the power supply prior to any intervention on the system.
l Fit a bipolar switch to the device power supply (use of Magnetoth- mal device with omnipolar switching is recommended)
l Check that a differential switch with a threshold of 0.03 A is installed upstream of the device.
l Do not install the equipment in an explosive atmosphere : the presence of flammable gas or fumes constitutes a serious safety hazard .
l The status of the system has a direct influence on the reliability and safety of the device.
l Anything not expressly envisaged in these instructions is not permitted .
l Store the instructions for future reference .
HAZARD
Ensure the device is not connected to the power supply before opening the cover hatch the casing in which it is contained .
THE INFORMATION CONTAINED IN THIS INSTALLATION MANUAL MAY BE SUBJECT TO CHANGE WITHOUT PRIOR WARNING .
Suppliers with verified business licenses
Audited Supplier 
){kind=link}
){kind=link}